COMPONENTS
Toyota Camry Hybrid AC Is Not Working? RepairPal will help you figure out whether it's your AC Refrigerant Leak, Climate Control Electrical Issue, AC Compressor, or something else.
OVERHAUL
HINT: COMPONENTS:
  • Toyota Camry 2018, Cabin Air Filter Element by Hastings®. This filter is specially designed and manufactured to reduce the amount of airborne pollutants and particles entering the cabin by capturing dust, pollen and other airborne. Fully meets OE requirements for fit and operation Reduces the level of contaminants, pollen, and dust in the cabin.
  • Detailed features and specs for the 2018 Toyota Camry including fuel economy, transmission, warranty, engine type, cylinders, drivetrain and more. Read reviews, browse our car inventory, and more.
  • Genuine 2018 Toyota Camry Heating and Air Conditioning Parts have been engineered to meet Toyota’s safety, reliability, and functionality standards. Plus, customize the OEM way with 2018 Toyota Camry Accessories. Explore Toyota Parts Online and shop an authorized dealer for all the spare 2018 Toyota Camry parts and accessories you need.
  1. DISCHARGE REFRIGERANT FROM REFRIGERATION SYSTEM
    SST 07110−58060 (07117−58080, 07117−58090, 07117−78050, 07117−88060, 07117−88070, 07117−88080)
  2. DISCONNECT COOLER REFRIGERANT SUCTION HOSE No.1
a. Install SST to piping clamp.
SST 09870−00015
HINT: Confirm the direction of the piping clamp claw and SST using the illustration showing on the caution label.
b. Push down SST and release the clamp lock.
NOTICE: Be careful not to deform the tube, when pushing SST.
c. Pull SST slightly and push the release lever, then remove the piping clamp with SST.
2018 toyota camry le manual air conditioner control lock box
d. Disconnect the cooler refrigerant suction hose No. 1.
NOTICE:
  • Do not use tools like screwdriver to remove the tube.
  • Cap the open fittings immediately to keep moisture or dirt out of the system.
3. DISCONNECT COOLER REFRIGERANT LIQUID PIPE A
SST 09870−00025
HINT: Disconnect cooler refrigerant liquid pipe A in the same way as the cooler refrigerant suction hose No. 1.
4. DISCONNECT HEATER OUTLET WATER HOSE
a. Using pliers, grip the claws of clip and slide the clip and disconnect the heater outlet water hose.

Disconnect heater outlet water hose

5. DISCONNECT HEATER INLET WATER HOSE
HINT: Disconnect in the same way as the heater outlet water hose.
6. REMOVE INSTRUMENT PANEL SAFETY PAD SUB−ASSY
HINT: Refer to the instructions for removal of the instrument panel safety pad sub−assy.
7. REMOVE AIR DUCT REAR No.1
a. Remove the 2 screws, bolt and nut.
b. Remove the air duct rear No. 1.

Remove air duct rear No.1

8. REMOVE AIR DUCT REAR No.2
  1. Remove the bolt and nut.
  2. A/X models: Remove the 2 screws, air duct rear No. 2 and console box mounting bracket No. 1.
  3. M/X models: Remove the screw, air duct rear No. 2 and console box mounting bracket No. 1.

Remove air duct rear No.2

9. REMOVE CONSOLE BOX DUCT No.1 (AUTO AIR CONDITIONING)
a. Remove the clip and console box duct No. 1.

Remove console box duct No.1 (Auto air conditioning)

  1. DISCONNECT FLOOR SHIFT PARKING LOCK CABLE ASSY
  2. REMOVE WINDSHIELD WIPER RELAY ASSY
  3. REMOVE INSTRUMENT PANEL BRACE SUB−ASSY No.1
a. Remove the 2 bolts and 2 earth wires.
b. Release the 2 clamps.
  1. Remove the bolt and screw.
  2. Remove the nut and instrument panel brace sub−assy No. 1.
13. REMOVE INSTRUMENT FINISH PANEL RETAINER LOWER
a. Remove the 2 bolts and instrument finish retainer lower.

Remove instrument finish panel retainer lower

14. REMOVE INSTRUMENT PANEL BRACE SUB−ASSY No.2
a. Remove the clamp, nut and passenger side junction block.
b. Remove the bolt and earth wire.
c. Remove the nut and clamp.
d. Remove the 2 nuts, bolt and instrument panel brace sub− assy No. 2.
15. REMOVE HEATER TO FOOT DUCT No.3
a. Remove the clip and heater to foot duct No. 3.

Remove heater to foot duct No.3

16. REMOVE HEATER TO FOOT DUCT No.1
a. Remove the clip and heater to foot duct No. 1.

Remove heater to foot duct No.1

17. DISCONNECT STEERING COLUMN ASSY
a. Remove the 3 nuts and driver side junction block.
b. Remove the 2 nuts and steering side connector block.
  1. Release the 2 clamps.
  2. Remove the 3 bolts, disconnect the steering column assy.
18. REMOVE INSTRUMENT PANEL REINFORCEMENT
a. Disconnect the 7 clamps and the wire harness.
b. Remove the 3 nuts, disconnect the 3 earth wires.
c. Remove the 3 caps, 7 bolts and instrument panel reinforcement.
19. REMOVE BLOWER ASSY
  1. Disconnect the connectors.
  2. Remove the screw, clamp and blower connector holder
c. Disconnect the 6 clamps and the wire harness.
d. Remove the 2 screws, 2 nuts and blower assy.
20. REMOVE DEFROSTER NOZZLE ASSY LOWER
a. Release the 4 fitting claws, remove the defroster nozzle assy lower.

Remove defroster nozzle assy lower

21. REMOVE AIR CONDITIONING RADIATOR ASSY
  1. Disconnect the connectors.
  2. Remove the 2 nuts and air conditioning radiator assy.

Remove air conditioning radiator assy

22. REMOVE MODE DAMPER SERVO SUB−ASSY
a. Remove the 3 screws and mode damper servo sub−assy.

Remove mode damper servo sub-assy

Mercedes-benz ntg4.5 v17.0 comand® 2017 download mp3. Mercedes-Benz – NTG4 DVD – 2017 (V17.0) This package contains two DVDs along with an information guide with coverage summary and instructions on how to install this map update in your Mercedes-Benz Navigation System. Truly every year, an average of 40,000 turn restrictions, 30,000 one-way streets, and 18,000 road signs are updated in the.
23. REMOVE HEATER RADIATOR UNIT SUB−ASSY
  1. Release the 2 fitting claws, remove the piping clamp.
  2. Remove the heater radiator unit sub−assy.
NOTICE: Prepare a support plate and waste to catch the leaked coolant.

Remove heater radiator unit sub-assy

24. REMOVE AIRMIX DAMPER SERVO SUB−ASSY
a. Remove the 3 screws and air mix damper servo sub− assy.
Issues

Remove airmix damper servo sub-assy

25. REMOVE AIR CONDITIONING TUBE ASSY
a. Remove the packing.
  1. Using a hexagon wrench 4 mm (0.16 in.), remove the 2 hexagon bolts and air conditioning tube assy.
  2. Remove the 2 O−rings from the air conditioning tube assy.
26. REMOVE COOLER EXPANSION VALVE
a. Remove the cooler expansion valve from the cooler evaporator sub−assy No. 1.

Remove cooler expansion valve

  1. REMOVE COOLER THERMISTOR No.1
  2. REMOVE COOLER EVAPORATOR SUB−ASSY No.1
a. Auto A/C model: Release the fitting claw, remove the 3 screws and air duct sub−assy.
  1. Remove the 12 screws and heater case LH.
  2. Remove the cooler evaporator sub−assy No. 1 from the heater case RH.
d. Remove the 2 O−rings from the cooler evaporator sub− assy No. 1.
29. INSTALL COOLER EVAPORATOR SUB−ASSY No.1
a. Apply compressor oil to the contact surfaces of 2 new O− rings and the cooler expansion valve and install them.
Compressor oil: ND−OIL 8 or equivalent
  1. Install the cooler evaporator sub−assy No. 1 to the heater case RH.
  2. Install the heater case LH with the 12 screws.
d. Auto A/C model: Install the air duct sub−assy with the 3 screws.
30. INSTALL COOLER EXPANSION VALVE
a. Install the cooler expansion valve to the cooler evaporator No. 1.
31. INSTALL AIR CONDITIONING TUBE ASSY

2018 Toyota Camry Le Manual Air Conditioner Control Module

  1. Apply compressor oil to the contact surfaces of 2 new O− rings and the air conditioning tube assy and install them.
    Compressor oil: ND−OIL 8 or equivalent
  2. Using a hexagon wrench 4 mm (0.16 in.), install the air conditioner tube assy and 2 hexagon bolts to the cooler evaporator sub−assy No. 1.
    Torque: 3.5 N·m (35 kgf·cm, 30 in.·lbf)
c. Install the packing.
HINT: Securely attach so that the gap in the packing will not be mode.
32. INSTALL AIR CONDITIONING RADIATOR ASSY
  1. Install the air conditioning radiator assy with the 2 nuts.
    Torque: 1.5 N·m (15 kgf·cm, 12 in.·lbf)
  2. Connect the connector.

Install air conditioning radiator assy

33. INSTALL DEFROSTER NOZZLE ASSY LOWER
a. Install the defroster nozzle assy lower.
NOTICE: After locating the pin 1. in the illustration, install 2., then 3.

Install defroster nozzle assy lower

34. INSTALL BLOWER ASSY
a. Install the blower assy with the 2 screws and 2 nuts.
Torque: 1.5 N·m (15 kgf·cm, 12 in.·lbf)
b. Install the 6 clamps, connect the wire harness.
  1. Install the blower connector holder with the screw and clamp.
  2. Connect the connectors.
35. INSTALL INSTRUMENT PANEL REINFORCEMENT
a. Install the instrument panel reinforcement with the 7 bolts and 3 caps.
b. Install the 3 earth wires with the 3 nuts.
c. Install the 7 clamps, connect the wire harness.
36. INSTALL STEERING COLUMN ASSY
  1. Install the steering column assy with the 3 bolts.
  2. Install the 2 clamps.
c. Install the steering side connector block with the 2 nuts.
Torque: 8.4 N·m (85 kgf·cm, 73 in.·lb
f)
d. Install the driver side junction block with the 3 nuts.
Torque: 8.4 N·m (85 kgf·cm, 73 in.·lbf)
37. INSTALL INSTRUMENT PANEL BRACE SUB−ASSY No.2
a. Install the instrument panel brace sub−assy No. 2 Ωith the 2 nuts and bolt.
b. Install the nut and clamp.
c. Install the earth wire with the bolt.
d. Install the passenger side junction block with the nut and clamp.
Torque: 8.4 N·m (85 kgf·cm, 73 in.·lbf)
38. INSTALL INSTRUMENT FINISH PANEL RETAINER LOWER
a. Install the instrument finish panel retainer lower with the 2 bolts.

Install instrument finish panel retainer lower

39. INSTALL INSTRUMENT PANEL BRACE SUB−ASSY No.1
  1. Install the instrument panel brace sub−assy No. 1 Ωith the nut.
  2. Install the bolt and screw.
    Torque: 9.8 N·m (100 kgf·cm, 87 in.·lbf) (Screw)
c. Install the 2 clamps.
d. Install the 2 earth wires with the 2 bolts.
  1. INSTALL INSTRUMENT PANEL SAFETY PAD SUB−ASSY
  2. INSTALL COOLER REFRIGERANT SUCTION HOSE No.1
  1. Lubricate new O−ring with compressor oil and install them to the hose.
    Compressor oil: ND−OIL 8 or equivalent
  2. Install the cooler refrigerant suction hose No.1 and piping clamp.
HINT: After connection, check the fitting for claw of the piping clamp.

Install cooler refrigerant suction hose No.1

42. INSTALL COOLER REFRIGERANT LIQUID PIPE A
HINT: Install in the same way as the cooler refrigerant suction hose No. 1.
  1. ADD COOLANT 3MZ−FE:
    1MZ−FE:
    2AZ−FE:
  2. CHARGE REFRIGERANT
    SST 07110−58060 (07117−58060, 07117−58070, 07117−58080, 07117−58090, 07117−78050, 07117−88060, 07117−88070, 07117−88080) Specified amount: 550 50 g (19.37 1.76 oz.)
  3. WARM UP ENGINE
  4. CHECK FOR ENGINE COOLANT LEAKS 3MZ−FE:
    1MZ−FE:
    2AZ−FE:
  5. INSPECT LEAKAGE OF REFRIGERANT
More about «Heater & air conditioner»:

Air conditioning system

Refrigerant

Air conditioning system

Refrigerant

Refrigerant line

V (cooler compressor to crankshaft pulley) beltNNo.1

Air conditioner control assembly

Air conditioning panel sub-assy

Air conditioning radiator assy

Air conditioning system

Blower assy

Cooler compressor assy (3MZ−FE)

Cooler compressor assy (1MZ−FE)

Cooler compressor assy (2AZ−FE)

Cooler condenser assy

Toyota Camry Service Manual / Heater & air conditioner / Air conditioning radiator assy